The mobile snow fences panels are used to protect the roads against the snow-drift. Snow fence is designed for controlling snow from drifting or to keep snow out of certain areas. As wind drifting snow barrier, the mesh netting needs to have high tensile strength. It is mostly made of strong, flexible plastic ( HDPE) material, which is difficult to break under heavy loading. The HDPE netting is also rolled up easily and installed easily.

Main color: Orange, black, dark green.
Raw material: HDPE with UV stabilized

Feature:
High strength
High visibility
Ageing resistance
Anti-corrosion
Aging resist
Softness and portability
Re-useable.

Mesh size: 70×40mm,80×40mm,100×40mm,100×50mm,110×40mm,80×26mm,90×26mm,100×26mm,110×26mm
Weight: 60-400grams/sqm can be manufactured
Width:1m,1.2m,1.22m,1.5m,1.8m
Length:20-100m is all available

Snow Fencing Projects

Snow fencing for Road & Transport Projects of Romania

Snow fence panels specifications:

The snow fences panels are made with the following accessories: - black wire of ø 3 mm- 0,273 kg/ panel

• M12 bolt, M12 bolt nut and grower washer- 1 set/ panel

The associated accessories with snow fences pieces are:

• black wire of ø 3 mm
• M12 * 50 bolt, M12 bolt nut and grower washer

The snow fences panels are made of a stiffed carriage at the angles, from OL 37ø18 concrete steel, of which there are attached, by rivet(A1 rivet, ø 5*10mm), fine metal foil tapes of ≠0,4 mm, 75 mm latitude.

At the apposition with the metal frame and with any cross between the fine metal foil, the stiffening is made by rivet.

Each panel will have two fixing flaps on the superior side (each one with M12 bolt and bolt nut and grower washer) and two clamps on the superior side.

The vertical bars of the snow fences main frame will be edged as to be thrusting in clay, at 250mm distance from the frames edge.
Each snow fences panel will have two flaps of ø 6 mm sealed to the main frame, through which a anchorage wire will float, and will fix the cable to the panels against the wind.

The panels will be coated in one single layer, painted with black paint in one coat.

The offered snow fences panels will honor exactly the heights needed.

Snow Fence and Chevron Tapes
Major materials:
Green Snow Fence, 1.5m x 2m
Black Snow fence, 1.5m x 2m
White and Green Chevron Tape in rolls

Snow Fencing for USA Snow-Storming Areas

Snow fencing made of high density polyethylene
The minimum mesh infill/grid size on the fencing shall be 4cm X 8 cm
Snow fencing:
Height 1.2m or 2.4m fence

Tips on Installation

Snow fence should be positioned upwind of the desired drift area, noting the prevailing wind direction.

1, Bury the fence posts 1/3 of their height, place the T-posts no more than 8' apart.
Note: Metal U-posts or rebar are not recommended as supports for snow fences.
Please note that when tensile strength is the biggest concern typically the posts are the weakest link in successfully controlling the snow drift.

2, Pull the snow fence taught and secure to the posts with plastic fence ties (zip ties) with a minimum 5" gap at the bottom of the fenceto prevent burying.  In addition, the snow fence should be attached on the upwind side of the post to prevent tearing. 

3, Loop the ties through the available holes or "teeth" in the post to prevent the snow fence from sliding down the post.  Support wires should stabalize end post to prevent sagging.

4, For additional longevity, pull the snow fence taught and secure between the flat side of the T-post and the wood slat. Or weave the slat through the fence mesh and use it as a tension bar to pull the fence snug.  Then secure the slat to the post.  Use plastic fence ties (zip ties) to secure the slat and snow fence to the T-post at the top, middle and bottom of the fence. Loop the tie through the "tooth" at the top and the bottom of the T-post to prevent the fence from sliding down the post.

5, For the greatest longevity of the snow fence it can be suspended from a wire (plastic, metal, rope etc.), this is in addition to the securing method described in #2 and #3.  The wire should be weaved through the upper openings of the snow fence and through the holes in the posts; the wire shall then be secured at both ends of the snow fence.

6, To connect snow fence sections, overlap both ends by at least 6" and weave a wood slat through overlapping strands.  Secure the joined area to a post.

Snow Safety Fencing Mesh Specifications Options